The garage door consists of two main parts one is a door and the other is its opener. A garage door opener is a device placed in homes, offices, and industries to open and close the door.

Steps to Install a Garage Door:

Below are the steps to install garage doors:

Step 1: Measurements

A garage door opener must be installed at the center of the door. Determine the exact location with tape to measure the width of a garage door. The center will be at half of this distance. On the inside part of the door draw a vertical line toward the top down the garage door center. Mechanism of raising and lowering of door joins at this line. The weight of the door must be balanced at this lifting point.

Step 2: Mark the Rail Position

Examine the top points of doors travel by raise and lower the door. Mark the points with chalk. Place the opener in the way rail must be placed higher than the apex of doors' travel track. If rail does not place higher than a door, whenever a door opens it strikes the rail.

Step 3: Support the Rail

Observe the area at the vertical dividing line above the door of the garage. There should be suitable support present in that area to help in binding the rails' front end. Install or place a front mounting board if there is no support present in that area.

Step 4: Attach the Rail

By following all the instructions given in the kit manual attach the rail on the garage door to the motor unit.

Step 5: Motor Assembly

The motor assembly is done on the place where the rail is parallel or horizontal with the door track. This position of motor assembly helps to determine a person that rail location does not interfere with the movement of doors. When it is placed at the exact position and height attach it with the ceiling bracket.

Step 6: Drawbar Attachment

To the rail, the carriage attaches a drawbar and move the door to its close position. Mark the holes of drawbar mounting screws on the door with the help of chalk. Place and tighten the hardware that fastens the drawbar to the door.

Step 7: Chain Driving Adjustments

Make all possible adjustments of the drive chain or screw lead by examining the exact location of bolts that limit the travel of the chain.

Step 8: Install Receiver and Push Button

A push-button and receiver should be installed to open and close the door. A simple bell wire is used for a push button. But be careful to place it at an exact position.

Step 9: Plugging

Plug the extension cord into the drive joining cord, and then plug the extension cord in the suitable electrical fitting. Use the push-button start garage door motion. To check no binding present anywhere pull the plug many times during the first test.

Step 10: Disconnection

The extension cord must be disconnected to plug the drive joining of the cord line into a permanently fixed outlet. Connect the line cord to the garage light socket if possible.

Garage Door Repair in Canada

Garage doors work on spring tension. The garage door moves on metal tracks on the wall with the help of a spring that provides power in moving. Sometimes the door does not properly work repair it. Ottawa Garage Doorsrepair garage door installation in Orleans offer their repair services to the people. They provide premium quality work and satisfaction to customers. Their experts repair the garage doors by tighten the screws, repair broken cables, and repair electric opener

Step 1: Check Metal Track

First of all, check the internal metal track. Check the ceiling brackets that hold track against the wall. If the screws of ceiling brackets are loose tightening them. If a person worked inside the garage so check crimps and dents on the track. If damage marks are found on track straighten them with a hammer, a piece of scrap wood, and a rubber mallet. The door must be replaced if the tracks are clumsily damaged.

Step 2: Check the Level of Tracks

Check the level of tracks that they are at their exact place or not. Horizontal tracks must decline down to the backside of the garage. Vertical tracks should be perpendicular to doors. Check that height of both tracks should be the same on the walls of the garage. If both tracks are not at their exact place, not remove but lose the bolts or screws that join the ceiling brackets and place tracks carefully at their exact place. Before tightening the bolts or screws recheck the level and exact position of both tracks. Then tighten the bolts or screws of the ceiling bracket.

Step 3: Cleaning of Tracks

Check tracks if there is any grease and dirt is presently clean. Hardened grease and dirt can be removed by the concentrated form of household cleaner. Rollers should be clean completely. Clean the roller dry and both tracks by wiping household cleaner.

Step 4: Check Loose Hardware System

Mark the loose hardware such as bolts or screws and tighten it when needed. Check the screws of plates are tight or not where spring is present on swing-up doors. If screws are loose tighten them. Check the joints that hold different door parts together on roll-up doors. If any screw is loose tighten it and replace damaged joints. The door sometimes hanging downward at one side. This sagging removes by servicing the joints. If cracks are found in the wood at the joint, fill the cracks by removing the joint and with the help of wood filler screw holes. Replace the screw if the screw hole is enlarged with a longer diameter screw of the hole's diameter. Add a hollow plug that should be dippedin carpenters' glue with a screw.

Conclusion

A garage is the most important part of the house that affects the look of a house. It is also used to store various valuable things or to place vehicles. So, select a durable and valuable door for the garage. Variety of doors available in the market that is opened and closed by motors. These doors install very easily. Sometimes the difficulty is found due to some loose screws, some damaged hinges, and cables. So, repair a garage door on an annual basis by cleaning it. Repairing increases the shelf life of the door.