Cedar is one of the few exterior materials that looks better after a decade of weather than it did on delivery day — provided it was specified correctly and detailed with some discipline. Get the grade, the exposure and the fastening wrong and you will be scraping cupped shingles off a wall in year seven. Get them right and the same wall will still be quietly doing its job when the roof is replaced. The difference is almost never the species. It is the decisions made before the first course goes up.
Shingles, shakes and pattern siding are not interchangeable
All three are cedar, and all three are often lumped together in a specification as "cedar siding." They behave very differently.
Shingles
Sawn on both faces, tapered, and relatively uniform in thickness. Because they are sawn, they lie flat and tight, which makes them the right choice when you want crisp shadow lines, close keyways, and a wall that reads as a single textured plane. Shingles accept stain evenly and are the usual pick for coastal and shingle-style houses where the finish is expected to weather to silver-grey rather than stay pigmented forever.
Shakes
Split rather than sawn on at least one face, thicker, and deliberately irregular. They throw deeper shadows and read as rustic even from the street. They also need more generous exposure and more attention to the layout of the butt lines, because the irregularity that makes them attractive will also broadcast a sloppy course line.
Pattern siding
Milled boards — bevel, channel rustic, shiplap, tongue and groove, board-and-batten stock — that go on in long runs. Pattern siding is faster to install over large uninterrupted elevations and gives you horizontal or vertical emphasis instead of texture. The trade-off is movement: a 10-inch-wide board moves far more across its width than a 5-inch shingle does, so cover widths, nailing patterns and end-grain sealing matter more.
The details that actually decide longevity
Cedar's natural extractives give it good decay resistance, but no wood survives being kept wet. Almost every cedar failure traces back to water that could get in and then could not get out.
•
A drainage gap. Battens, a rainscreen mat, or breathable spacer mesh behind shingles and siding let the back face dry. On a shaded north wall or in a humid coastal climate this is not optional, it is the whole ballgame.
•
Stainless or hot-dipped fasteners. Cedar's tannins corrode plain steel and the resulting black streaks run the length of the wall. Stainless ring-shank is the safe default; electro-galvanized is not.
•
Two nails per shingle, placed above the butt line of the course above. Over-nailing restrains movement and splits shingles. Under-nailing lets them lift.
•
Back-priming or pre-staining all six faces before installation if the wall will be finished. A factory-applied or dipped finish on the back and ends is cheap insurance against uneven moisture uptake.
•
Keyway spacing. Leave the gap the manufacturer calls for between adjacent shingles and offset keyways by a sensible margin from course to course. Tight keyways plus wet wood equals buckling.
•
Clearance at grade, roofs and decks. Keep the bottom course well above splash zones and flashings, and keep sprinklers off the wall.
For a careful walkthrough of layout, exposure and fastening sequence on a real wall, the trade-level guide to
siding with cedar shingles from a builders' journal is worth reading before you order material, because it will change how much you buy.
Exposure, grade and the arithmetic of ordering
Exposure — the amount of each shingle left visible — governs both appearance and coverage. Reduce exposure and you get tighter shadow lines, more layers of protection and considerably more material per square. Increase it and you save material but lose redundancy. Sidewall exposures are typically more generous than roof exposures, and the number you choose should be consistent across every elevation, including the small ones above a porch roof where it is tempting to fudge.
Grade matters just as much. Clear, all-heartwood, vertical-grain material stays flat and takes finish predictably; lower grades with flat grain and sapwood are perfectly usable in the right place but will cup and shed finish sooner on a sun-blasted southwest wall. Order a sensible waste allowance — corners, dormers, curved walls and woven corners eat material fast — and condition the bundles on site, stacked and covered with air circulation, rather than letting them sit shrink-wrapped on wet ground.
Timbers: the structural jewelry of an exterior
Exposed timbers do disproportionate work on a facade. A pair of bracketed outlookers under a gable, a porch beam with a chamfered edge, a pergola with properly proportioned posts — these are the elements people photograph. They are also the elements most often under-sized, because a timber that looks correct in a drawing frequently looks spindly once it is outdoors with sky behind it. As a rough rule, go one dimension heavier than instinct suggests for anything cantilevered or silhouetted.
Cedar timbers are attractive here because they are relatively light for their section, stable, and naturally decay-resistant where they meet weather. Detail the tops with a slight slope or a metal cap, keep end grain off masonry, and accept that large sections will check as they dry — checking is cosmetic in most cases, not structural, and it is part of why heavy timber reads as handmade rather than extruded.
Where sourcing becomes a design decision
The practical limit on most cedar exteriors is not design ambition but availability of the right section, grade and species in one place — a 6x10 porch beam, matching pattern siding, white cedar shingles for the upper walls and a custom moulding profile to tie them together. Working with a specialist supplier such as Liberty Cedar, a
timbers supplier that also carries cedar shingles and shakes, Western red cedar lumber, pattern siding, white cedar and Atlantic white cedar stock, mouldings and custom millwork, keeps those elements consistent instead of stitched together from three sources with three different moisture histories. It also means the conversation about grade, section and profile happens before the order is cut, which is the point at which it is still cheap to change your mind.
Finishing: decide once, early
There are really three paths. Leave cedar bare and let it weather to grey, which is low-maintenance but uneven on walls with partial shade. Use a penetrating semi-transparent stain, which keeps colour and is re-coated rather than stripped. Or paint, which looks sharp but demands back-priming, tight joint sealing and a rainscreen, because trapped moisture pushes film finishes off from behind. Choosing between them is partly aesthetic and partly a maintenance commitment, and it is worth understanding how exterior-grade coatings behave differently from interior ones — the discussion of whether
exterior paint can be used inside a luxury home is a useful reminder that these products are formulated for very specific exposure conditions and are not casually swapped.
A short pre-order checklist
1. Fix the exposure for every elevation and calculate coverage from that number, not from square footage alone.
2. Confirm species and grade per wall based on sun, shade and splash exposure.
3. Specify the rainscreen method and the fastener metallurgy in writing.
4. Size exposed timbers generously and detail their tops and end grain.
5. Pick the finish strategy before material arrives so back-priming can happen off the wall.
6. Order mouldings and trim profiles with the siding so colour and grain character match.
None of this is exotic knowledge. It is simply the set of choices that separates a cedar exterior people admire in year fifteen from one that becomes a renovation line item. Make them deliberately, and the wood will do the rest.